Hubbardton-forge 137720 User Manual download pdf

Assembly & Installation Instructions A276

Erlenmeyer 4-Light Pendant 13-7720 Page 1 of 3

Hand-Forged, Vermont-Made Lighting and Accessories

P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735

26494

To Assemble Canopy (Figure 1)

Component Parts

A .38” Hex Nipple (2)

B .50” Hex Nipple(longer) (2)

C Lock Washer (4)

D Canopy

E Canopy Pipe (4)

F Ceiling Bracket

1. Carefully unpack canopy from carton.

2. Line up end of canopy pipe (E) with hole in canopy (D).

3. Place hex nipple (A) through lock washer (C), down through

holes in canopy (D) and thread into canopy pipe (E). Tighten

securely. Repeat twice.

4. Place longer .50” hex nipple (B) through lock washer (C),

down through holes in ceiling bracket (F) and canopy (D)

thread into canopy pipe (E). Tighten securely. Repeat twice.

To Assemble Fixture

(Figures 2 & 3)

Component Parts

D Canopy

E Canopy Pipe (4)

G Fixture pipe (4)

H Clutch sleeve (4)

I Clutch (4)

J Set Screw (4)

1. Slip the wires from the fixture pipe (G) into and through the

canopy pipe (E) up through the canopy (D).

2. Unscrew the clutch (I) from the canopy pipe (E); slide it across

the wires and onto the fixture pipe (G). Follow this with the

plastic clutch sleeve (H), oriented so the tapered end of the

clutch sleeve nests in the clutch (Figure 2). Slide the canopy pipe

(E) as far as necessary to give you the total length of the fixture

which you desire. Be careful not to scratch the pipe surfaces and to

pull excess wire up through the canopy pipe (E). Screw clutch (I)

onto canopy pipe (E). There must be a minimum 1-1/2" of inner pipe inside the outer pipe. Hand-tighten the clutch

to temporarily hold this adjustment. The clutch is not securely fastened at this point; do not depend on it to hold the

fixture.

Important: To ensure full connection strength, be sure the tapered end of the plastic clutch sleeve is

oriented toward the clutch when assembled and securely tighten set screw (Figure 2).

Stop. Please see installation

instructions on next page.

3. Once the fixture is fastened to the ceiling, tighten the set screw (J) firmly with hex wrench provided. Only after the

set screw (J) is tight should you install the glass.

(continued)

CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL

INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician.

This product must be installed in accordance with applicable installation code(s), by a person familiar with the

construction and operation of the product and the hazards involved.*

Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.

(Figure 2)

(Figure 1)

1 2 3

A276 1
26494 1

Summary of Contents

Page 1 - 26494

Assembly & Installation Instructions A276 Erlenmeyer 4-Light Pendant 13-7720 Page 1 of 3 Hand-Forged, Vermont-Made Lighting and Accessori

Page 2

Assembly & Installation Instructions A276 Erlenmeyer 4-Light Pendant 13-7720 Page 2 of 3 Hand-Forged, Vermont-Made Lighting and Accessori

Page 3

Assembly & Installation Instructions A276 Erlenmeyer 4-Light Pendant 13-7720 Page 3 of 3 Hand-Forged, Vermont-Made Lighting and Accessori

Comments to this Manuals

No comments

Hubbardton-forge 137720 User Manual

Browse online or download User Manual for Lighting Hubbardton-forge 137720. Hubbardton Forge 137720 User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Lighting Hubbardton-forge 137720