Hubbardton-forge 19124810SG User Manual download pdf

HUBBARDTONFORGE.COM

-, -   

154 RT. 30 SOUTH

•

CASTLETON, VERMONT 05735

32320

Assembly & Installation Instructions

If you need further assistance, or nd that you are missing any parts, please contact the dealer from which you purchased this product.

We hope you enjoy your xture!

* Hubbardton Forge will not be liable for injury or damage caused by improper installation, lamping or use of this xture.

Install the Canopy (Figure 1)

Component Parts

A Crossbar

B Threaded Nipple

C Lag Screw (2)

D Lock Nut

CAUTION: BE SURE POWER IS OFF AT THE MAIN BREAKER BOX

PRIOR TO INSTALLATION.

CAUTION: THIS FIXTURE MUST BE SUPPORTED INDEPENDENTLY OF

AN OUTLET BOX. CROSSBAR IS DESIGNED TO FIT IN THE BOTTOM

OF A STANDARD METAL 4” OCTAGONAL OUTLET BOX.

1. Drill two holes through the back of the outlet box and us-

ing two lag screws (C) attach cross bar (A) to a structural

member in the ceiling, centering the crossbar in the outlet

box. We've supplied lag screws with your xture; however,

different materials and/or construction methods may require

different fasteners. If in doubt, contact a qualied electrician.

2. Thread the nipple (B) into the crossbar (A).

3. Thread lock nut (D) and threaded loop (G) onto nipple, then

place canopy (E) over threaded loop and adjust nipple

length to ensure a snug canopy t. Once the length is de-

termined, set the canopy aside and lock nipple position by

tightening the locknut (D) against the crossbar (A).

4. Attach one end of the chain (H) to the xture loop (I).

5. Attach the other end of the chain to the threaded loop (G)

and thread the xture wires through every other link of the

chain (H) and up through the threaded loop (G) and nipple

(B) into the outlet box.

6. Using suitable wire connectors (not provided), connect

xture wires to supply wires (white or ribbed side of xture

cord to white supply, black or smooth side of xture cord

to black supply, and bare copper to bare copper or green

supply). Ground the crossbar (A) using the ground screw (J),

cupped washer (K) and hex nut (L) to secure a pigtail lead to

the crossbar. Push wires back into outlet box.

A382

For Aegis Chandelier 19124810SG

Page 1 of 2

CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL INJURY OR DEATH AND

PROPERTY DAMAGE. We recommend installation by a licensed electrician. This product must be installed in accordance with

applicable installation code(s), by a person familiar with the construction and operation of the product and the hazards involved.*

Caution: Do not exceed maximum wattage noted on xture. Use only recommended bulbs with xture.

(Continued)

(Figure 1)

E Canopy

F Loop Collar

G Threaded Loop

H Chain

I Fixture Loop

J Ground Screw

K Cupped Washer

L Hex Nut

1 2

Summary of Contents

Page 1 - CASTLETON, VERMONT 05735

HUBBARDTONFORGE.COM-, -   154 RT. 30 SOUTH • CASTLETON, VERMONT 05735 32320Assembly & Installation Inst

Page 2

If you need further assistance, or nd that you are missing any parts, please contact the dealer from which you purchased this product. We hope you en

Comments to this Manuals

No comments

Hubbardton-forge 19124810SG User Manual

Browse online or download User Manual for Lighting Hubbardton-forge 19124810SG. Hubbardton Forge 19124810SG User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Lighting Hubbardton-forge 19124810SG